Search Catalog
        
 All Products    CPA/CBA Series, Clevis Load Pins
All Products > Load Pins > CPA/CBA Series, Clevis Load Pins > Item # CPA-2.75  
Download PDF Download PDF     Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Item # CPA-2.75, Load Pins


Image




Dimensional Drawing  · Performance Specs  · Specifications  · Electrical Specifications  · General Information

Dimensional Drawing

Dimensional Drawing


Performance Specs

Overload without Zero Shift
150%

Overload without Failure
300% (Minimum)

Bridge
Full bridge 350 Ohm (Nominal)

Excitation
12 V AC (Maximum)
12 V DC (Maximum)

Output Signal1
2-mV/V (Nominal)
2-mV/V (Standardized Output)

Non-Repeatability
±0.15% FS (Nominal)

Non-Linearity
±0.50% FS (Nominal)

Hysteresis
±0.50% FS (Nominal)

Service Temp Range
to 150 °F

Temp Effects (on Zero)
0.005% FS / °F (Nominal)

Temp Effects (on Output)
0.008% load / °F (Nominal)

Zero Balance2
±2% FS (Nominal)
1 Exact output provided with calibration data. (Standardized outputs are optional). In addition, Strainsert factory calibrations are intended to simulate installed conditions, however, it is recommended that an in-place calibration be performed to account for any installation, tolerance, and/or alignment influences affecting sensor measurement.
2 Prior to loading, it is necessary to initially/periodically null the zero load output to account for any residual offset.


Specifications

Load Capacity
100,000 lb

Material
Stainless Steel 17-4, H-1025 (Standard)

A - Width of Center Loading Section
2 in

B - Width of Clevis Support Section
1-1/8 in

C - Length of Pin/Bolt Reduced Section, Instrumented Zone
11/16 in

Dp - Nominal Pin Diameter
2.748 in

E - Active Length of Pin
5-5/8 in

F - Clevis Pin Head Length
2 in

H - Width of Keeper Plate Slot
13/32 in

J - Depth of Keeper Plate Slot
1/2 in

Lp - Overall Length of Pin
8-3/8 in

W - Allowance for Retaining Ring Installation
3/4 in

Keeper Plates
SPA-100-112-1-A

Connector Type
Axial Connector
Permanently Attached Axial Cable


Electrical Specifications

Receptacle
PTIH-10-6P

Mating Plug
PT06A-10-6S (SR)

     Function
Pin

     (+) Excitation
A

     (-) Excitation
D

     (+) Signal
B

     (-) Signal
C

Cable
#20(26x34) AWG., rubber insulation, shielded, rubber jacket, 4-Conductor (Standard Cable)

     Function 
Wire Code

     (+) Excitation 
Red

     (-) Excitation 
Black

     (+) Signal 
Green

     (-) Signal 
White


General Information
  • Precison Load Sensing
  • Rugged
  • Internally Sealed Strain Gages
  • Easy Installation
  • Direct Force Measurement
  • High Strength Stainless Steel


 MORE IMAGES 

·  Clevis Pin with Two Shear Planes

·  CPAdim_new

·  Force F Direction


 DOWNLOADS 

CPA-CBA Load Pin Ordering Information
(PDF, 173KB)

Load Pin Installation
(PDF, 614KB)

Strainsert Force Calibration Service
(PDF, 407KB)

Load Sensing Clevis Pin Quick Start Guide
(PDF, 229KB)



 Renewal Parts 


page100
Standard Cable

PT1H-10-6P
PT1H-10-6P
Transducer Receptacles

more available ..


 Accessories 


Keeper Plate
SPA-100-112-1-A
Keeper Plate